Search found 389 matches

by Beretta1234567
Wed Apr 13, 2016 9:04 pm
Forum: General Discussion
Topic: Motor mounts?
Replies: 2
Views: 2270

Motor mounts?

Does 96 Mounts fit on a 93 Beretta?

Can I put a 4t60 (non-e) in place of the 3t40?
by Beretta1234567
Sun Jan 31, 2016 10:04 am
Forum: Drag Racing, Auto-x and Track events
Topic: Beretta 1/4 mile times
Replies: 157
Views: 170034

Re: Beretta 1/4 mile times

Thanks for posting this list, it gives me an idea what to expect.
by Beretta1234567
Sun Dec 20, 2015 4:58 pm
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Re: Engine wants to rev up again, have no idea why...

Unplugged the MAF and readjusted the pins and it doesn't seem to throw any MAP codes anymore.
No more stalling on a warm/hot start.
I'll have to test it some more to make sure the revving stopped for good.
by Beretta1234567
Wed Dec 16, 2015 8:40 pm
Forum: General Discussion
Topic: What muffler would you buy?
Replies: 3
Views: 4694

What muffler would you buy?

I am looking for a muffler with good air flow on a 90 Beretta
by Beretta1234567
Tue Dec 08, 2015 11:25 am
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Re: Engine wants to rev up again, have no idea why...

I havent had time to check the maf plug to make sure its good.
Or blocking the egr to test for it being stuck open?
I have to hold the gas pedal a bit to keep it from stalling and I hold the idle about 750 rpm.
by Beretta1234567
Sat Dec 05, 2015 11:02 am
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Re: Engine wants to rev up again, have no idea why...

I havent had time to block off the EGR Yet, I have been really bussy, I did get time to check codes again. New development, MAF low input code 102 showed up after a week or two of the revving problem not happening. Possible the MAF was reading low enough the engine revved up to compensate and now it...
by Beretta1234567
Wed Nov 25, 2015 9:34 pm
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Re: Engine wants to rev up again, have no idea why...

Unfortunately, the IAC count is the only thing my scanner can't read.

How would a stuck open EGR cause the car to behave?
How can I check this?
by Beretta1234567
Tue Nov 24, 2015 11:34 am
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Re: Engine wants to rev up again, have no idea why...

I always considered them as close to oem as possible without buying dealer oem.

Car still has the problem. Showed up again.
No SES lights or codes ever when this problem happens.
Only fix is turn it off and on again.
by Beretta1234567
Sat Nov 21, 2015 5:35 pm
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Re: Engine wants to rev up again, have no idea why...

We checked my car up against a known good Beretta, everything was the same. However when my problem happened sometimes it would not be 0% throttle position at 0%. It read 5% at 0% throttle.
by Beretta1234567
Fri Nov 20, 2015 7:50 pm
Forum: Diagnostic Help
Topic: Engine wants to rev up again, have no idea why...
Replies: 14
Views: 6950

Engine wants to rev up again, have no idea why...

1996 Beretta 3100 v6 automatic Replaced: Throttle position sensor (No Change). Idle air control (No Change). ECM (Problem was fixed). Engine revs up to 2800 RPM, however only if I get the car on the freeway (Typical freeway speeds 65-70 MPH). temporary fix: Put car in neutral and turn engine off, wa...
by Beretta1234567
Tue Nov 03, 2015 3:37 pm
Forum: For Sale
Topic: REDUCED-1990 White GTZ For Sale, South Louisiana $4400
Replies: 57
Views: 28841

Re: REDUCED-1990 White GTZ For Sale, South Louisiana $4400

I couldn't tell because there was a side conversation going on part way through.
by Beretta1234567
Wed Oct 28, 2015 11:05 am
Forum: General Discussion
Topic: Can someone tell me which pins are these on the ECM?
Replies: 5
Views: 3290

Re: Can someone tell me which pins are these on the ECM?

Need some help if possible.

Is there something missing?
According to this it should work?
by Beretta1234567
Sat Oct 17, 2015 12:12 pm
Forum: General Discussion
Topic: Can someone tell me which pins are these on the ECM?
Replies: 5
Views: 3290

Re: Can someone tell me which pins are these on the ECM?

Cliff8928 wrote:What year and engine?
1990 Beretta 3.1 v6 automatic.