Search found 711 matches
- Sun Jul 15, 2007 8:20 am
- Forum: General Discussion
- Topic: Just bought a Beretta
- Replies: 6
- Views: 3078
Just bought a Beretta
Welcome!
- Fri Jul 13, 2007 7:12 am
- Forum: Wheels and Tires
- Topic: How wide of a wheel can you run?
- Replies: 4
- Views: 3265
How wide of a wheel can you run?
Impressive!
- Wed Jul 11, 2007 9:05 pm
- Forum: Performance Mods
- Topic: This isn't what you want to find under the hood
- Replies: 6
- Views: 2902
This isn't what you want to find under the hood
So did you add some support to the bracket while you had the welder going?
- Sun Jul 08, 2007 8:53 am
- Forum: Diagnostic Help
- Topic: 1995 Z26 Ac problems
- Replies: 4
- Views: 2133
1995 Z26 Ac problems
No. They didn't put all of them in the same place. Perhaps someone with your year car can. Otherwise you will have to feel or listen to them to see which one is activating. I'm pretty sure they will be located in a group of 3-4 relays under the hood on the firewall or over by the passengers side ...
- Sat Jul 07, 2007 9:56 pm
- Forum: Diagnostic Help
- Topic: 1995 Z26 Ac problems
- Replies: 4
- Views: 2133
1995 Z26 Ac problems
Probably not a lot. There will be a relay, a sensor (which you probably cannot test without a scan tool that reads live PCM data) and wire that goes to the compressor. If there is no voltage to the compressor then there likely is no command from the PCM. You would have to find a wiring diagram. ...
- Thu Jul 05, 2007 7:26 am
- Forum: Diagnostic Help
- Topic: Coolant boiling over
- Replies: 3
- Views: 2258
Coolant boiling over
This doesn't sound good......
I hope this oil change was with a mechanic you trust and have a history with.
I hope this oil change was with a mechanic you trust and have a history with.
- Thu Jul 05, 2007 7:24 am
- Forum: Diagnostic Help
- Topic: Permenant High Beams
- Replies: 10
- Views: 5016
Permenant High Beams
Are you sure it is broken. Many times you can just reach up there and "adjust" the switch by bending the bracket a little (usually toward the rod) and then they start working again.
- Thu Jul 05, 2007 7:22 am
- Forum: BFest Archive
- Topic: Sooo......
- Replies: 16
- Views: 2098
Sooo......
Bstuff has lots of pics links posted.
Nitro if you are talking about my old car.... The POS JVC deck and generic amp were in the car when I purchased it. I never cared what radio was in that car. I listened to music everywhere I went, but it rarely came from speakers.
Nitro if you are talking about my old car.... The POS JVC deck and generic amp were in the car when I purchased it. I never cared what radio was in that car. I listened to music everywhere I went, but it rarely came from speakers.
- Mon Jul 02, 2007 11:33 pm
- Forum: Performance Mods
- Topic: No more stock V-6 for me
- Replies: 26
- Views: 8778
No more stock V-6 for me
Yes, which is rather silly.....
- Sun Jul 01, 2007 8:40 am
- Forum: Suspension and Brakes
- Topic: Caliper
- Replies: 3
- Views: 2287
Caliper
I'd take it to the shop (if you can trust them) and see what they say. They might be willing to work with you.
I'd guess you need a new caliper bolt or steering knuckle, or new threads in that one hole. Rather hard to diagnose over the internet.
I'd guess you need a new caliper bolt or steering knuckle, or new threads in that one hole. Rather hard to diagnose over the internet.
- Sun Jul 01, 2007 8:38 am
- Forum: Board Suggestions
- Topic: We are in time for a buy and neeeed advice
- Replies: 1
- Views: 2872
We are in time for a buy and neeeed advice
The throttle position sensor could have a bad spot in it, which could cause problems that you would notice at slow throttle application. Usually they wear out in a common range that the pedal moves first. Some engines have a certain RPM that they have a harmonic imbalance and there will always be a...
- Sun Jul 01, 2007 8:32 am
- Forum: Performance Mods
- Topic: No more stock V-6 for me
- Replies: 26
- Views: 8778
No more stock V-6 for me
Were here for you Chazz.....
There should be a little up and down play on the shaft but very little in and out play. If the shaft spins and the impellers do not contact the housings then you will be ok. The turbo has oil lubricated brass bushings and they always have some play in them.
There should be a little up and down play on the shaft but very little in and out play. If the shaft spins and the impellers do not contact the housings then you will be ok. The turbo has oil lubricated brass bushings and they always have some play in them.
- Fri Jun 29, 2007 7:44 pm
- Forum: Diagnostic Help
- Topic: service engine soon light
- Replies: 3
- Views: 2279
service engine soon light
I would probably clean the IAC and the TB. If the car is not missing under load then I would not suspect the ignition system. If it misses at idle then I would suspect a bad injector. You need to check all of the spark plugs and see what condition they are in. They will tell you more about each c...
- Fri Jun 29, 2007 7:37 pm
- Forum: Diagnostic Help
- Topic: air condition conpres
- Replies: 10
- Views: 3702
air condition conpres
Post in the for sale / wanted section.
I guess english is not your first language?
I guess english is not your first language?
- Thu Jun 28, 2007 9:46 pm
- Forum: Diagnostic Help
- Topic: air condition conpres
- Replies: 10
- Views: 3702
air condition conpres
Depends on which model, but most are down at the bottom of the engine compartment at the front. it has the AC lines running in and out of it. If you have to ask much more I suggest doing a LOT of reading, or letting a professional work on your AC. It will get very expensive and you don't want to s...