Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colorado
Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colorado
Hello all,
I did a little garage inventory today as I still have a few Beretta parts sitting around that I won't ever use. I would be happy to ship any of these if the buyer wants to pay for it, or I can deliver to Bfest for you. Here's what I have:
1x Z51 Rear Swaybar with good mounts.
1x Original GM "Beretta" splash window decal in Red (this was an accessory part from GM that I loved on my GT)
1x Resurfaced Quad 4 Flywheel (this was already turned and is ready to install - the pic shows it a little discolored from some brake parts cleaner that spilled on plastic that was on it - should polish right out).
1x Set of 17x7 Konig GT-R wheels. This set of wheels has the 5x100 and 5x115 pattern on it, so it will work on Beretta's as well as other GM FWD. I purchased these from a Beretta owner and put them on my wife's W-Body. I had them powdercoated in Black Chrome Metallic and they were on the car for about 2 years. There are a few chips in them, but overall they look very nice. The tires on them have about 3/32's left on them, so you could drive on them for a few thousand miles, but will need to be replaced soon. They are a bit dusty in the pics as they have been under my house for 4+ years.
I have several sets of prototype phenolic spacers that I had done up for all of the Beretta engines. These are supposed to reduce intake temps while increasing runner length and increasing top end power. Supposedly these were suppose to give between 2-5HP gains depending on the engine. These are prototype units that have never been on a car, but should fit with no problems. I'd post a link to some more info, but I can't. Google "Phenolic Spacer" and choose the first option for Grimmspeed for the WRX/STI and it gives some good explanation on how they work.
I have uploaded pictures of all of these items here (and I've got to write this is sudo since I can't post links...lol). dub dub dub period tranzgenic period comm and then go to forsale slash beretta
I'm open to offers on all of this stuff - I've been out of it for too long to know what it goes for so lets haggle
Thanks!
I did a little garage inventory today as I still have a few Beretta parts sitting around that I won't ever use. I would be happy to ship any of these if the buyer wants to pay for it, or I can deliver to Bfest for you. Here's what I have:
1x Z51 Rear Swaybar with good mounts.
1x Original GM "Beretta" splash window decal in Red (this was an accessory part from GM that I loved on my GT)
1x Resurfaced Quad 4 Flywheel (this was already turned and is ready to install - the pic shows it a little discolored from some brake parts cleaner that spilled on plastic that was on it - should polish right out).
1x Set of 17x7 Konig GT-R wheels. This set of wheels has the 5x100 and 5x115 pattern on it, so it will work on Beretta's as well as other GM FWD. I purchased these from a Beretta owner and put them on my wife's W-Body. I had them powdercoated in Black Chrome Metallic and they were on the car for about 2 years. There are a few chips in them, but overall they look very nice. The tires on them have about 3/32's left on them, so you could drive on them for a few thousand miles, but will need to be replaced soon. They are a bit dusty in the pics as they have been under my house for 4+ years.
I have several sets of prototype phenolic spacers that I had done up for all of the Beretta engines. These are supposed to reduce intake temps while increasing runner length and increasing top end power. Supposedly these were suppose to give between 2-5HP gains depending on the engine. These are prototype units that have never been on a car, but should fit with no problems. I'd post a link to some more info, but I can't. Google "Phenolic Spacer" and choose the first option for Grimmspeed for the WRX/STI and it gives some good explanation on how they work.
I have uploaded pictures of all of these items here (and I've got to write this is sudo since I can't post links...lol). dub dub dub period tranzgenic period comm and then go to forsale slash beretta
I'm open to offers on all of this stuff - I've been out of it for too long to know what it goes for so lets haggle
Thanks!
-Aaron
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
How thick are the phenolic spacers?
Where are you located?
Where are you located?
95' BRM Z26. cammed/ported 3400/3500 Hybrid. HM282, OBD2, Garret T3/T04E 60 Trim, IC.heavywoody wrote:Beretta, fast, reliable, and cost effective are words that should not be used in the same sentence.
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
I'm not at home right now so I can't measure them, but if I recall correctly they are all 1/4 inch units.
-Aaron
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
Also guys, I apparently can't reply to PM's yet (lame), so you may want to give me an e-mail address or an alternative way to get ahold of you if you PM me.
-Aaron
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
i want the wheels
1990 Beretta GTZ 1995 Beretta Z26 1996 Beretta Z26
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
ErichZ26 wrote:i want the wheels
Wheels are sold!
-Aaron
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
Here is the link to the pics since it appears I can now post it:
http://www.tranzgenic.com/forsale/beretta/
http://www.tranzgenic.com/forsale/beretta/
-Aaron
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
Only interested in some that are 1" thick. If you happen to have a set, lemme know. Thanks!Stencil wrote:I'm not at home right now so I can't measure them, but if I recall correctly they are all 1/4 inch units.
95' BRM Z26. cammed/ported 3400/3500 Hybrid. HM282, OBD2, Garret T3/T04E 60 Trim, IC.heavywoody wrote:Beretta, fast, reliable, and cost effective are words that should not be used in the same sentence.
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
What would you want for the sway bar? And maybe the spacers of the 3.1
1989 Beretta Base 2.8
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
HOLY CRAP - IT'S AARON! Long time no see, buddy. How ya been??? I remember back in 05 when I bought my SRT4 you told me to hang onto the GTZ... I was naive and didn't listen... Sold it and regretted it for almost 8 years. Finally found another 93 Quasar GTZ in January.
1993 Quasar Quad4 GTZ - Project WTF
Previous Berettas: 90 GT, 93 Quasar GTZ, 93 Garnet GTZ, 93 Aqua GT
Previous Berettas: 90 GT, 93 Quasar GTZ, 93 Garnet GTZ, 93 Aqua GT
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
PM Sent via Facebook.
1989 GTU - The Nice Car
1989 GTU Mock - The Neglected Car
1989 Base Model - The Rally Car
1989 GTU Mock - The Neglected Car
1989 Base Model - The Rally Car
Re: Misc Parts - Wheels, Decal, Spacers, Z51 Swaybar! - Colo
The 3.1 spacers, wheels and Z51 swaybar are sold.
-Aaron
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M
'92 Beretta GTZ 2.3L 5M - Undergoing "unibody off" restoration ATM (almost done!)
'93 Beretta GT "MISEREE" 3.1 5M
'95 Beretta Base DGGM 2.2 5M
'96 Beretta "FAUXZ26" 2.2 5M