custome itb?
- ShaneLT(ShaneZ26)
- Registered User
- Posts: 504
- Joined: Sun Aug 15, 2010 12:27 pm
- Location: Leamington, Ontario
custome itb?
I was looking around and found these.
http://www.zccjdm.com/catalog.php/azcar ... DY_#IMAGES
Or
http://www.zccjdm.com/catalog.php/azcar ... TTLE_BODY_
Could either of these be used to make an itb setup on a 3X00?
http://www.zccjdm.com/catalog.php/azcar ... DY_#IMAGES
Or
http://www.zccjdm.com/catalog.php/azcar ... TTLE_BODY_
Could either of these be used to make an itb setup on a 3X00?
Re: custome itb?
Yeah they will all work. You can also look into other cars that come with ITB's from the factory. I think the 4age ae86 corollas may have. The r34 skyline gtr also has them with the rb26.
Street bikes also use them.
Street bikes also use them.
- ShaneLT(ShaneZ26)
- Registered User
- Posts: 504
- Joined: Sun Aug 15, 2010 12:27 pm
- Location: Leamington, Ontario
Re: custome itb?
I was looking.g at some other v6's but most are i6 and they come pairs of 2's like 3 see of 2. I'm gonna keep looking tho.
- Money pit Beretta
- Registered User
- Posts: 6411
- Joined: Thu Jul 26, 2007 11:36 am
- Location: Kansas
Re: custome itb?
The hood is a bit low for that kind of thing. Unless you plan to put a double wide cowl hood on. All and all not a bad idea, but there is no plenum(less that double wide cowl hood). The linkage would be hard to make.
There is a big problem with the stock upper intake. As the number 3 valve is closing number 4 is stealing flow from it and so on all the way to six. There is an offset on 1 and 2 so it's not that bad. A custom upper would help some, but the high cost and the small gain of say 10 to 15hp is crazy(but is efficient in all of the power band). Still I dream of this upper with equal length runners and the right placement of the runners with a good plenum. We have the throttle cable length to push the plenum out some, but again this is just a dream.
I have a few books on this kind of thing. Not to say I know alot! Just trying to make something that someone else came up with better. GM is not looking for the best, just what works at a low cost.
There is a big problem with the stock upper intake. As the number 3 valve is closing number 4 is stealing flow from it and so on all the way to six. There is an offset on 1 and 2 so it's not that bad. A custom upper would help some, but the high cost and the small gain of say 10 to 15hp is crazy(but is efficient in all of the power band). Still I dream of this upper with equal length runners and the right placement of the runners with a good plenum. We have the throttle cable length to push the plenum out some, but again this is just a dream.
I have a few books on this kind of thing. Not to say I know alot! Just trying to make something that someone else came up with better. GM is not looking for the best, just what works at a low cost.
keep'em flying!
- ShaneLT(ShaneZ26)
- Registered User
- Posts: 504
- Joined: Sun Aug 15, 2010 12:27 pm
- Location: Leamington, Ontario
- Money pit Beretta
- Registered User
- Posts: 6411
- Joined: Thu Jul 26, 2007 11:36 am
- Location: Kansas
Re: custome itb?
They sure could, you would need an adapter of some sort. That would make them stick up even more. The upper is about 2 1/2 inches tall plus the vac tube that would be around three inches.
The ITB's should be taller than that. Then you must also think about the EGR and the where to get vacuum for the brake booster and all other vacuum needs.
Look man I'm not trying to shoot down your project. There are just alot of things to do to get this to work.
You could use breathers for the PCV system, but by far that's not as good as the stock system.
The ITB's should be taller than that. Then you must also think about the EGR and the where to get vacuum for the brake booster and all other vacuum needs.
Look man I'm not trying to shoot down your project. There are just alot of things to do to get this to work.
You could use breathers for the PCV system, but by far that's not as good as the stock system.
keep'em flying!
- ShaneLT(ShaneZ26)
- Registered User
- Posts: 504
- Joined: Sun Aug 15, 2010 12:27 pm
- Location: Leamington, Ontario
- daguse5853z
- Registered User
- Posts: 268
- Joined: Sun Feb 12, 2006 7:35 pm
- Location: Central, PA
Re: custome itb?
You're talking custom custom custom. You can make anything work in anything if you have skills
- SuzukiGhostRider
- Registered User
- Posts: 2464
- Joined: Tue Feb 12, 2008 4:07 am
- Location: Milan NM
- Contact:
Re: custome itb?
Unless you were going to cut six holes in the UIM to mount 6 ITB's to, you'd HAVE to use the LIM and block off the mount hole for the UIM. Again, as stated, you'd also have to find a new way to feed vaccum.
- scd88ga
- Registered User
- Posts: 1828
- Joined: Mon Jun 28, 2010 9:02 pm
- Location: Wisconsin Rapids, Wisconsin
- Contact:
Re: custome itb?
I'll sell ya some carbs! They are off of a 225hp Yamaha V6 Outboard boat motor!
'94 Quad 4 H.O. 5 speed Z26, Red & Rare! 1 of 896 Quad Z26's and of those it's 1 of 167 red paint/gray interior!
Need A Quality Used Part? Contact me at Posihead Auto Parts!
https://www.facebook.com/pages/Posihead ... 3779691724
Need A Quality Used Part? Contact me at Posihead Auto Parts!
https://www.facebook.com/pages/Posihead ... 3779691724
-
- Registered User
- Posts: 1068
- Joined: Sun Nov 02, 2003 11:54 am
- Location: Paulden, AZ
- Contact:
Re: custome itb?
^^^^that would be tits to see on a 3X00 motor!
Geoff
95 Base V6: Current Project; Work In Progress
95 Base V6: Current Project; Work In Progress
Re: custome itb?
There's a guy who makes ITB setups for quads. The place is called quad4rods.com or something. He's got quite a bit of neat stuff and could prolly give helpful advice if you were serious about heading down that route.
Jon
Jon
88 GTU 5spd 67k black
89 GTU 3500/5spd swapped 79k white
08 TBSS LS2 AWD
89 GTU 3500/5spd swapped 79k white
08 TBSS LS2 AWD
- 3X00-Modified
- Administrator
- Posts: 10912
- Joined: Thu Jul 05, 2007 9:18 am
- Location: Brooklyn CT
Re: custome itb?
TCE Has already made a set. Dave is currently using them on his 3500 in his Z28.
http://60degreev6.com/forum/showthread. ... post427509
http://60degreev6.com/forum/showthread. ... post427509
Re: custome itb?
I can't remember the firing order but would spliting the intake into a front and rear bank solve this?
92 3.1 manual base 190k Daily
93 3.1 auto base 275k RIP 'Joan'
73 Yamaha RD250 moth balled
CPL, USMC, Veteran/2111