6 speed for your 3x00??? Check this out.

Want to know how to get more out of your Beretta? Or have a mod you would like to share?
Alpinestar10
Registered User
Posts: 452
Joined: Thu Oct 28, 2010 10:27 pm
Location: GRAND RAPIDS MI

Re: 6 speed for your 3x00??? Check this out.

Post by Alpinestar10 »

Nice so what flywheel did you use the dual mass? Or? Im going to consider this when i have another cavi or beretta. i got a 282 sitting in the garage but newer tech i like. Are you using a lsd?


User avatar
Rettax3
Registered User
Posts: 1805
Joined: Mon Oct 22, 2012 3:34 pm

Re: 6 speed for your 3x00??? Check this out.

Post by Rettax3 »

Thanks guys, nice to hear positive feedback. I know there are a lot of reasons NOT to do one of these swaps too. I used the stock 3800 flywheel for a ~'96 Camaro. It is much thicker and heavier than the 60-degree V-6 flywheels*, which helped eliminate the need for a costly clutch-spacer and custom clutch. It will also help avoid some of the problems encountered with these swaps when using light-weight flywheels that eventually cause damage to the transmission due to vibrations. As for LSD, it costs between $1200 and $1600 for a good LSD for this transmission. With it being brand new, I had no interest in splitting the case and more than doubling my cost for the project, even though Limited Slip would be awesome to have here. Maybe I will look into it again if I ever have to rebuild this tranny...

*The 3800 flywheel is so much thicker in fact, that I actually had to make 1/4" spacers between the 5-speed 282 and the engine on the original build with this car years ago, or have the flywheel milled-down. I built the spacers so I could use standard 3800 flywheels, rather than pay for custom machine-work. And that choice is paying off again here.


1989 SuperCharged 3800 Srs-II (First)Six-Speed GTU
1990 Turbo 3.4 5-Speed T-Type
1990 4.0L 4-Cam 32-Valve V-8 5-Speed Indy GTi (Project)
1990 Stock(!) 3.1 MPFI Auto Indy
1995 LA1/L82 4T60E Z-26
1995 3.4 DOHC Turbo 5-Speed Z-26
BerettaLove32
Registered User
Posts: 297
Joined: Wed May 29, 2002 5:40 pm
Location: Chicago
Contact:

Re: 6 speed for your 3x00??? Check this out.

Post by BerettaLove32 »

Awesome work, that is one cool and unique Beretta. You can tell a lot of time an effort went into the car.


MY91GT(Z)
Registered User
Posts: 1255
Joined: Sun Mar 12, 2006 12:11 am
Location: Rochester New York
Contact:

Re: 6 speed for your 3x00??? Check this out.

Post by MY91GT(Z) »

You find uniquely awesome work to your cars and it awesome that u do.it.on budget and mostly.with gm parts also and thats what makes even better... now.time.to turn ur attn on green indy to see what thats like :)hehe


User avatar
Rettax3
Registered User
Posts: 1805
Joined: Mon Oct 22, 2012 3:34 pm

Re: 6 speed for your 3x00??? Check this out.

Post by Rettax3 »

MY91GT(Z) wrote: now.time.to turn ur attn on green indy to see what thats like :)hehe
:twisted: That is my next project (as planned, anyway, so I hope... :roll: ). The car is currently parked at a family member's house, so I have to move it here first (not a short trip, either), but the garage is open and waiting. After that is a five-speed swap into my '86 Fiero GT (fastback), and the twin-turbo 4.6 Northstar into my 'not old' Camaro, with an upgrade to a stronger five-speed transmission than the one already in it.
I would love to put one of these six-speeds into the Teal Indy too, but with the L47 Quad-Cam 32 Valve V-8 in there, it physically will not fit without butchering the car, which I will not do. Clearance is only off by an inch or so too :roll: .


1989 SuperCharged 3800 Srs-II (First)Six-Speed GTU
1990 Turbo 3.4 5-Speed T-Type
1990 4.0L 4-Cam 32-Valve V-8 5-Speed Indy GTi (Project)
1990 Stock(!) 3.1 MPFI Auto Indy
1995 LA1/L82 4T60E Z-26
1995 3.4 DOHC Turbo 5-Speed Z-26
heavywoody
Global Moderator
Posts: 1991
Joined: Sun Nov 03, 2002 4:10 pm
Location: Concord, NC
Contact:

Re: 6 speed for your 3x00??? Check this out.

Post by heavywoody »

Would you mind posting up a list of parts that you used, and what cars they came from, for the community?


Geoff
95 Z26 Turbo 3400 5spd - R&D Project
Beretta Preservation Society - Director of Acquisitions
Image
User avatar
woody90gtz
Registered User
Posts: 4698
Joined: Thu Jul 11, 2002 8:45 pm
Location: Walton, NY
Contact:

Re: 6 speed for your 3x00??? Check this out.

Post by woody90gtz »

That is awesome. And you cut a LOT of cost from what I was figuring. Sweet deal. I'd like to know how it all went together and if it reliably shifts well.


91 "SS" - WOT 3400/5spd - 13.29@101.6 - World's fastest N/A FWD Beretta
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
User avatar
Rettax3
Registered User
Posts: 1805
Joined: Mon Oct 22, 2012 3:34 pm

Re: 6 speed for your 3x00??? Check this out.

Post by Rettax3 »

heavywoody wrote:Would you mind posting up a list of parts that you used, and what cars they came from, for the community?
I'm still hoping to get a build-thread together on this soon. But a quick list of parts is handy enough:

~$530 Including Freight: F40 six-speed transmission, 0-miles (new)
$170 Both 2005 Cobalt SS 2.0 SC Five-speed CVs, Saab 9-3 Turbo (IIRC) Six-speed Intermediate shaft (I don't recall the year though, any of the six-speed cars of the era should work) (all parts used, factory OEM)
$75 1995 Ford Ranger 3.0L Stage-3 6-puck clutch friction disc (new)
~$50 2001 Pontiac Grand Am Dorman CM640069 clutch master-cylinder/line assy.
$60 Redline MT-85 Synchromesh Synthetic transmission fluid
~$2 O2 Sensor plug (transmission filler-plug)
$75 Dakota Digital SGI-5C Speedometer calibration unit
Just under $1000.

Keep in mind though that I already had a Stage-3 complete clutch kit in my car for ~half a year, so the friction-disc was the only thing I needed to swap (since the F40 input shaft is so much larger). I also modified the transmission bell-housing itself to make it seat 5/16" closer to the engine, so I didn't need to buy the $300-500 custom clutch assembly with an extended center (splined) section, or a V-8 Archie flywheel spacer. On a 60-degree V-6, the flywheel thickness is a serious problem for this transmission, and the way I built this wouldn't work for that engine. But here is an idea: The 2.8 and 3.1 used on the F-body cars (Camaro and Firebird) is much thicker than the FWD cars' flywheels... I think they might be balanced differently too, but that is a very minor point to deal with. :wink:
The clutch master cylinder had to be tweaked, but could have been easier if my car wasn't already set up for the five-speed, maybe.
The left CV joint (they are the same on either side) had to be shortened by ~1".
I also fabricated the shift-cable bracket on the transmission myself.
I would say a more realistic number for anyone not wanting to do a lot of fab-work themselves would be closer to $1500, because of the CV and the shift-cable bracket (although I don't know who you would go to, aside from maybe V-8 Archie, and they may not even be able to help you because the Fiero shift-cables come in from the opposite direction). The Jack-shaft (Intermediate shaft) bearing needs a custom mount too, even if using a 3X00. Piece of cake on my 3800 though... This is assuming the F-Body flywheel works too...

I can say it isn't necessarily the ideal upgrade -an add-on double-overdrive sixth gear to a new or rebuilt Muncie/Getrag 282 would be closer to perfect from my view, but that doesn't exist. So here is this option instead...

BTW, avoid lightweight flywheels and un-sprung clutch-discs if considering this tranny -from my research, those are the two things that kill the F40s...
woody90gtz wrote:That is awesome. And you cut a LOT of cost from what I was figuring. Sweet deal. I'd like to know how it all went together and if it reliably shifts well.
Thank you, I appreciate that. I'll be putting some miles on it here pretty soon, at least enough to test the overall setup to make sure there are no major bugs to work out. I've done enough modifications on the parts that I do have some concerns regarding reliability, and although the F40 is rated for 400 N-M of input torque (hence the designation), it doesn't have a sterling reputation. My engine puts out significantly higher numbers than the 3900 VVT engine that originally came with the F40 (the 3900 was rated 240/240 HP and ft-lbs torque, the stock L67 3800 SC is rated for 240/280 HP and torque -the torque-rating is allegedly under-rated and is closer to 310 ft-lbs torque, and mine is modified a bit with higher compression, WAI, lighter internals, headers and low-restriction short-run dual exhaust, so I'm conservatively estimating closer to 280 HP), so I won't be babying it once I've got the tranny out of break-in. It WILL get a fair test.


1989 SuperCharged 3800 Srs-II (First)Six-Speed GTU
1990 Turbo 3.4 5-Speed T-Type
1990 4.0L 4-Cam 32-Valve V-8 5-Speed Indy GTi (Project)
1990 Stock(!) 3.1 MPFI Auto Indy
1995 LA1/L82 4T60E Z-26
1995 3.4 DOHC Turbo 5-Speed Z-26
User avatar
Travelor
Global Moderator
Posts: 508
Joined: Fri Jan 25, 2008 10:15 pm
Location: Neenah, WI
Contact:

Re: 6 speed for your 3x00??? Check this out.

Post by Travelor »

I'm interested in seeing the photos you took during installation. I'd like to see clearances and closer pictures of the changes you made to the housing as well as how the flywheel fits.


1988 GTU
1990 GTZ
Beretta Preservation Society Chairman
Image

"Have you painted your car in a parking lot today?"
User avatar
GTZfan
Registered User
Posts: 304
Joined: Thu Oct 28, 2010 3:20 pm

Re: 6 speed for your 3x00??? Check this out.

Post by GTZfan »

Thats amazing. Great work rettax. I'd love to see your exotic creations/modifications in person.


Image
1991 GTZ Quad4 black, all original, low miles. Beretta Calendar 2008, 2009, 2015
1992 GTZ Quad4 quaser, completely restored. Beretta Calendar 2011, 2012, 2013 images of the shiny quaser
Post Reply