Pauly's 90 GTZ rebuild.
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
yup, it seems to have an issue with 'iat'? did i get that right? or the butterfly is just open at idle.woody90gtz wrote:Gotta make sure they can take a beating before you install them. hahaKFLO 93 GT wrote:Hahahaah, I'm with Chad, when I have sweet parts around that aren't installed - I tend to molest them quite a bit.
Pauly is that the TB Eric had?
Re: Pauly's 90 GTZ rebuild.
IAT is idle air temperature. You mean IAC. Idle air control. Your TB is either letting in too much air, or your IAC is dirty, stuck open or completly bad.
My Motortopia
Bfest Committee 2012, 2013, 2014
Bfest AND Bust 2012 Winner: First ever clutch swap at Berettafest!
Bfest 2013 Watermelon Award: Boob shaped hood dents FTW
- woody90gtz
- Registered User
- Posts: 4703
- Joined: Thu Jul 11, 2002 8:45 pm
- Location: Walton, NY
- Contact:
Re: Pauly's 90 GTZ rebuild.
Yup. When you datalog it, your IAC counts should be in the 30 range or so. If the counts are too low, that means the butterfly is open too far and the IAC can't close enough to bring the idle down.
91 "SS" - WOT 3400/5spd - 13.29@101.6 - World's fastest N/A FWD Beretta
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
96 "T56" LS/6spd/8.8 RWD swap - 13.45@104.7 lol
GEARHEAD dezign youtube
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
long over due update:
@ Bfest NE, little Jon adjusted my TB, it was a set screw that was causing the TB from closing all the way. Engine (idle) runs a lot better.
did another Dyno, 176.7 HP @ 6700rpm, 142.7 torque
This week coming up i will receive yet another custom chip from Jeff council. Dyno to come...
@ Bfest NE, little Jon adjusted my TB, it was a set screw that was causing the TB from closing all the way. Engine (idle) runs a lot better.
did another Dyno, 176.7 HP @ 6700rpm, 142.7 torque
This week coming up i will receive yet another custom chip from Jeff council. Dyno to come...
Last edited by Red_Bra_Black_GTZ on Mon Sep 01, 2014 3:36 pm, edited 1 time in total.
- scd88ga
- Registered User
- Posts: 1828
- Joined: Mon Jun 28, 2010 9:02 pm
- Location: Wisconsin Rapids, Wisconsin
- Contact:
Re: Pauly's 90 GTZ rebuild.
It'd be nice to see W41 CHP numbers at the wheels on your next dyno! If you come to Bfest next year, can I get a ride?
'94 Quad 4 H.O. 5 speed Z26, Red & Rare! 1 of 896 Quad Z26's and of those it's 1 of 167 red paint/gray interior!
Need A Quality Used Part? Contact me at Posihead Auto Parts!
https://www.facebook.com/pages/Posihead ... 3779691724
Need A Quality Used Part? Contact me at Posihead Auto Parts!
https://www.facebook.com/pages/Posihead ... 3779691724
- 3X00-Modified
- Administrator
- Posts: 10912
- Joined: Thu Jul 05, 2007 9:18 am
- Location: Brooklyn CT
Re: Pauly's 90 GTZ rebuild.
Which year W41 though? he's only 9hp off of 93... 14hp from the 91-92 numbers...
It's a fun car, I took it for a drive with Paul after we fixed the TB set screw.
It's kinda funny, everyone wants W41 stuff and its really only worth 10hp. I honestly thought it was more than that.
It's a fun car, I took it for a drive with Paul after we fixed the TB set screw.
It's kinda funny, everyone wants W41 stuff and its really only worth 10hp. I honestly thought it was more than that.
- scd88ga
- Registered User
- Posts: 1828
- Joined: Mon Jun 28, 2010 9:02 pm
- Location: Wisconsin Rapids, Wisconsin
- Contact:
Re: Pauly's 90 GTZ rebuild.
Haha, 91-92 W41 obviously! More power!!! UGH UGH UGH! 93 W41's lost 5hp due to having a lower flowing cylinder head. His car has the better flowing one! I know W41 cams/chip only add 10hp, but when combined with a header, and full exhaust it really wakes the car up! Plus a bit of a lopy idle just sounds cool! lol3X00-Modified wrote:Which year W41 though? he's only 9hp off of 93... 14hp from the 91-92 numbers...
It's a fun car, I took it for a drive with Paul after we fixed the TB set screw.
It's kinda funny, everyone wants W41 stuff and its really only worth 10hp. I honestly thought it was more than that.
'94 Quad 4 H.O. 5 speed Z26, Red & Rare! 1 of 896 Quad Z26's and of those it's 1 of 167 red paint/gray interior!
Need A Quality Used Part? Contact me at Posihead Auto Parts!
https://www.facebook.com/pages/Posihead ... 3779691724
Need A Quality Used Part? Contact me at Posihead Auto Parts!
https://www.facebook.com/pages/Posihead ... 3779691724
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
when i show up, ask me then..scd88ga wrote:It'd be nice to see W41 CHP numbers at the wheels on your next dyno! If you come to Bfest next year, can I get a ride?
paul
- SuzukiGhostRider
- Registered User
- Posts: 2464
- Joined: Tue Feb 12, 2008 4:07 am
- Location: Milan NM
- Contact:
Re: Pauly's 90 GTZ rebuild.
Are those WHP number or CHP numbers? I would assume WHP but just wondering?
Small correction to a previous statement. W41 CAMS only make 10hp extra. As stated when combined with better springs, a header, an 086 head (vs a 753 head the W41 SCX's came with) and maybe a light port'n'polish,a tune,etc. it can add up to 40hp+ if you know what you're doing. And that's just TOP END work...
Small correction to a previous statement. W41 CAMS only make 10hp extra. As stated when combined with better springs, a header, an 086 head (vs a 753 head the W41 SCX's came with) and maybe a light port'n'polish,a tune,etc. it can add up to 40hp+ if you know what you're doing. And that's just TOP END work...
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
I had my calipers powder coated. They will be on the car by friday.
rear
rear
front
front
front
rear
rear
front
front
front
- snowblindburd
- Administrator
- Posts: 1148
- Joined: Sun Sep 25, 2005 8:48 pm
- Location: Wisconsin
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
old pics from the big rebuild of march-june 2011
my pretty engine dawg with an ass photo bomb free flowing cat headers hanging low dyno run...
my pretty engine dawg with an ass photo bomb free flowing cat headers hanging low dyno run...
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
2009, the installation of newly grinded W 41 cams
intake cam exhaust cam extrude and honed intake log
intake cam exhaust cam extrude and honed intake log
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact:
Re: Pauly's 90 GTZ rebuild.
august 2009 w 41 cam swap build up.
ported and polished head compression test
ported and polished head compression test
-
- Registered User
- Posts: 378
- Joined: Tue Sep 11, 2007 3:02 pm
- Location: Montreal, QC
- Contact: