looking for vent visors and driver door strip molding

List any Item for a Beretta that you want to purchase
Post Reply
JAWS89GTU
Registered User
Posts: 186
Joined: Sun May 08, 2011 10:40 pm

looking for vent visors and driver door strip molding

Post by JAWS89GTU »

Looking for the rain visors and also need the driver door molding as well as the rear quarter molding for my gtu...I believe 88 and 89 gt's have the same molding I need....and the last thing is a driver side tail light...let me know and shipping costs or if ya live close ill gladly pick them up...thanks


John
User avatar
DTMAce
Registered User
Posts: 3510
Joined: Thu Sep 25, 2008 7:03 pm
Location: Michigan EUP
Contact:

Re: looking for vent visors and driver door strip molding

Post by DTMAce »

Rain visor's? Or vent visors? Those are on the door jamb correct? If so, I have 2 you can have for 10 bucks shipped from the 94 base.
94' Z26 Project - 95' Base Project - Custom LED Light Conversions!
Chosen Proposal Submission & Committee Member for Beretta Fest 2012 in Traverse City Michigan

Image
Image
JAWS89GTU
Registered User
Posts: 186
Joined: Sun May 08, 2011 10:40 pm

Re: looking for vent visors and driver door strip molding

Post by JAWS89GTU »

Yea the vent visors..the things that allow you to have the window open a little bit...are they new or used?
User avatar
DTMAce
Registered User
Posts: 3510
Joined: Thu Sep 25, 2008 7:03 pm
Location: Michigan EUP
Contact:

Re: looking for vent visors and driver door strip molding

Post by DTMAce »

Never mind. You are looking for rain shields/drip moldings, etc. Vents are the things IN the door jamb, they are located above the door striker stud.... Small panels, about 3 inches wide, maybe 7-8 inches tall, have vents in them. I don't have any rain/drip trim. Those are aftermarket items.
94' Z26 Project - 95' Base Project - Custom LED Light Conversions!
Chosen Proposal Submission & Committee Member for Beretta Fest 2012 in Traverse City Michigan

Image
Image
2.2H8TA
Registered User
Posts: 915
Joined: Mon Aug 31, 2009 3:59 am
Location: NE-PA
Contact:

Re: looking for vent visors and driver door strip molding

Post by 2.2H8TA »

I just bought vent shades from autozone. They don't have em' in stock, but they order them, and it takes about a week to get. They cost $42.39. I have not installed them yet, and they are the ones which go up inside the molding, not the stick on ones. They are made by Ventvisor. I'm not selling mine, I have plans for them, but they are readily available. There is an older white GT in a yard a few blocks from me, I'll try and go down to check the moldings on it sometime this coming week.
1994 AQUA ZED
JAWS89GTU
Registered User
Posts: 186
Joined: Sun May 08, 2011 10:40 pm

Re: looking for vent visors and driver door strip molding

Post by JAWS89GTU »

Ok cool let me know if they are in good shape and ill take a drive up there...which yards is it...denaples?
2.2H8TA
Registered User
Posts: 915
Joined: Mon Aug 31, 2009 3:59 am
Location: NE-PA
Contact:

Re: looking for vent visors and driver door strip molding

Post by 2.2H8TA »

It's at the Anthracite junk yard in west Scranton. I'll check it out as soon as I get my car back. I also hear that harrys-u-pull it has alot of berettas, I have yet to take a trip down there though.
1994 AQUA ZED
JAWS89GTU
Registered User
Posts: 186
Joined: Sun May 08, 2011 10:40 pm

Re: looking for vent visors and driver door strip molding

Post by JAWS89GTU »

I went to harrys in hazleton about 3weeks ago and they only had 3 berettas and 1 was a z26 which I took out the seats from I've never been to the one in pennsburg nor allentown but if you do go can you also check out the driver taillight for me as well please as I need one...thanks
User avatar
Chad91GTZ
Registered User
Posts: 1354
Joined: Thu Dec 23, 2004 8:32 pm
Location: Lomira, WI

Re: looking for vent visors and driver door strip molding

Post by Chad91GTZ »

2.2H8TA wrote:I just bought vent shades from autozone. They don't have em' in stock, but they order them, and it takes about a week to get. They cost $42.39. I have not installed them yet, and they are the ones which go up inside the molding, not the stick on ones. They are made by Ventvisor. I'm not selling mine, I have plans for them, but they are readily available. There is an older white GT in a yard a few blocks from me, I'll try and go down to check the moldings on it sometime this coming week.

Ive been LOOKING for the vent shades that stick up in the molding. Do you have a part number?
Image
My Motortopia

Bfest Committee 2012, 2013, 2014
Bfest AND Bust 2012 Winner: First ever clutch swap at Berettafest!
Bfest 2013 Watermelon Award: Boob shaped hood dents FTW
2.2H8TA
Registered User
Posts: 915
Joined: Mon Aug 31, 2009 3:59 am
Location: NE-PA
Contact:

Re: looking for vent visors and driver door strip molding

Post by 2.2H8TA »

It says on the box, the sticker on the package, and the recipt 92135. I'm guessing thats it.
1994 AQUA ZED
User avatar
Beretta_gal
Registered User
Posts: 127
Joined: Wed Apr 14, 2010 11:51 pm
Location: Whitehall,MI

Re: looking for vent visors and driver door strip molding

Post by Beretta_gal »

Just for the record...JC Whitney also sells the vent visors for $43-$44 that is where I bought one pair of mine...the other pair I bought from Auto Zone as well...same brands.... ;)
Beretta_gal
It's a BERETTA thing...All others just don't understand!!!
2012 Bfest Winner
Post Reply