Plastics, shift plate, tail lights, UPDATED 1/5/12

beretta · Post by **beretta** » Thu Feb 23, 2012 10:22 pm

i have the flywheel cover and wheel well plastic for passenger side no holes ripped, but the size of the box to ship is going to be huge unless i can fold it around and squeeze it in a smaller box without wrecking it.

going to check out the condition of the shift plate in my 96 the one in the 94 i just got i think the lettering is wore i dont care what one i have in my own car so i can swap them if mine is good.

Slinky · Post by **Slinky** » Thu Feb 23, 2012 10:30 pm

ok thanx dude

Slinky · Post by **Slinky** » Sun May 20, 2012 9:39 pm

still need a mint shift plate!

Alpinestar10 · Post by **Alpinestar10** » Sun May 20, 2012 10:29 pm

why buy a mint one that will cost a good dime and not pay some one to pin strip the while back on a faded one?

SummitBalt08 · Post by **SummitBalt08** » Sun May 20, 2012 10:31 pm

Or could make a decal to go exactly over where the original letters are. Could be done easily I would imagine.

Alpinestar10 · Post by **Alpinestar10** » Mon May 21, 2012 1:35 am

The letters look raised to me im not positive though

Slinky · Post by **Slinky** » Mon May 21, 2012 12:15 pm

Cost is no object, i have money and i need a mint one asap

scd88ga · Post by **scd88ga** » Tue May 22, 2012 3:31 am

Having somebody paint that lettering isn't gonna happen, then lettering isn't raised, and a decal would be a good possibility and may hold up/look better than the OE stamped writing. Has anyone noticed that the OE stamped on writing is quite crooked on them! LMAO!

Slinky · Post by **Slinky** » Wed May 23, 2012 12:24 pm

DITTO scd

More added

Slinky · Post by **Slinky** » Mon Jul 02, 2012 12:12 pm

Still needed..

GTU89 · Post by **GTU89** » Tue Jul 03, 2012 1:38 am

Where are you located?

I believe I have a very nice auto shift plate (two actually, but one is in use on the Beretta) It does not have a trunk release button on it, but it is easy to fit one to it (I did on the one I used)

I'll have to check again but I believe that the writing on it is intact as well. Not sure of the year, but IIRC its almost black whereas the one I used on mine is a bluish/gray color. I think the ribbon for the shifter is a bit wrinkled on it but that can be swapped easily I believe.

Slinky · Post by **Slinky** » Tue Jul 03, 2012 12:21 pm

I am located at 15666
And i dont need the ribbon ect, just the actual black plate with good writing on it, i also now need a window switch cover with good writing as well, pm me a pic if possible and lmk a price shipped thanx!

GTU89 · Post by **GTU89** » Tue Jul 03, 2012 10:42 pm

Ah, I just checked it a bit ago and I was wrong about the writing, the writing on this one is completely gone.

Slinky · Post by **Slinky** » Thu Jul 05, 2012 9:18 pm

Sadfaceeee..

Slinky · Post by **Slinky** » Mon Sep 17, 2012 9:47 pm

updated, got cash still need this stufff

Beretta.net

Plastics, shift plate, tail lights, UPDATED 1/5/12

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Wheel well plastics, shift plate ect

Re: Supercharger, Plastics, shift plate, MORE ADDED 5-22-12

Re: Supercharger, Plastics, shift plate, MORE ADDED 5-22-12

Re: Supercharger, Plastics, shift plate, MORE ADDED 5-22-12

Re: Supercharger, Plastics, shift plate, MORE ADDED 5-22-12

Re: Supercharger, Plastics, shift plate, MORE ADDED 6-3-12

Re: Supercharger, Plastics, shift plate, MORE ADDED 6-3-12

Re: Supercharger, Plastics, shift plate, MORE ADDED 6-3-12

Connect with your social network account