Wiring Harness

1988GTU · Post by **1988GTU** » Sun May 20, 2012 1:53 pm

Looking for a good unmolested engine and dash harness for a 1990 3.1 MPFI Automatic trans Beretta. NON digital cluster.

scd88ga · Post by **scd88ga** » Tue May 22, 2012 4:40 am

Hmm, I'll look to see what's available by me.

1988GTU · Post by **1988GTU** » Tue May 22, 2012 9:21 am

Ok thanks.

BRich Beretta · Post by **BRich Beretta** » Tue May 22, 2012 3:06 pm

If you can get me some specific details as to where to go to directly pull these entire harnesses out of car there is a 89 GT automatic at junkyard I would be willing to pull it out of for you if its not a pain in the arse.

1988GTU · Post by **1988GTU** » Tue May 22, 2012 3:56 pm

Basically you unbolt the connectors at each corner of the engine bay as well as from any ground/power connection and unplug all connectors attached to the main harness to free it up. If you grab that harness, be sure to grab the fuel injector harness with it, that's important.

BRich Beretta · Post by **BRich Beretta** » Wed May 23, 2012 9:53 am

does it go through firewall into car? if you can snap some shots of your bay and show these connectors that are bolted to car that would be great. I don't wat to guess which ones they may or may not be.
I'm assuming you arent asking for the entire harness that runs through engine bay?
Thanks

Post by **3X00-Modified** » Wed May 23, 2012 10:33 am

He's asking for the whole wiring harness inside and out... so that means disconnect everything till its free and pull it all out.

1988GTU · Post by **1988GTU** » Wed May 23, 2012 1:56 pm

3X00-Modified wrote:He's asking for the whole wiring harness inside and out... so that means disconnect everything till its free and pull it all out.

I cant put it anymore simpler than that.

Blacklit · Post by **Blacklit** » Fri May 25, 2012 12:34 pm

you might try to message ronaconda. he pulled one for me just a few months ago. cost me $100 shipped

1988GTU · Post by **1988GTU** » Fri May 25, 2012 10:28 pm

Ok will do! Ty!

speedy · Post by **speedy** » Sat May 26, 2012 8:45 am

if your in pa, go to harry's in hazleton pa, or ez pull and save in new ringold, theres not a lot of beretta's there right now, maybe 10 or so between the 2, but there 45mins from each other, its a nice drive, and theres a good chance you'll find the part you want, or something else you'll want.

1988GTU · Post by **1988GTU** » Sat May 26, 2012 8:47 am

I am in Michigan.

speedy · Post by **speedy** » Sat May 26, 2012 9:52 am

move to pa, its better here!

btw, i absolutly love this new smiley!!!
:deadhorse:

1988GTU · Post by **1988GTU** » Sat May 26, 2012 11:02 am

PAsh!

scd88ga · Post by **scd88ga** » Tue May 29, 2012 3:54 am

Yo! I have an 89 Beretta auto, a 91 Beretta auto and I think a 90 Corsica auto I can get good harnesses from. $100 shipped. Let me know if any of those will suit your fancy! lol

Beretta.net

Wiring Harness

Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Re: Wiring Harness

Connect with your social network account